REAL-TIME SEG SIMULATOR
CLASSIFIEDFull physics simulation at 60 FPS with 3D visualization, tactical telemetry, and AI analyst commentary. All equations derived directly from Searl's original documentation. START to initiate priming sequence.
The SEG Architecture
Three concentric stator rings
Each static ring carries a ring of freely-orbiting rollers. The counts 12 / 22 / 32 follow the Law of Squares: perimeter grows, mass grows, the collective vortex reinforces. With only one ring the system always fails.
Material layers (inside → out)
Magnetization Designer — Searl's Printing Recipe
Searl's secret: apply a strong DC field of 150–180 A through a 200-turn copper winding, then superimpose a tiny 0.1–0.2 A AC at 1–3 MHzthrough a 10-turn copper strip wound on top. The total MMF must stay strictly positive at all times — the AC modulates the DC, it never inverts it. Duration: a single 9-second on-off cycle.
SEG Voltage Calculator
Searl's reference: 250 km/h → 0.6845 V per roller dielectric.
Law of Squares Validator
Low Voltage Extraction Designer
One C-core coil per roller on the periphery. Rollers pass through the air gap of the cores. Target around 526 Hz per coil, 0.6 mm wire, 20–30 turns.
Exact Dimensions — Searl Blueprints
Roller (rodillo)
| Layer | Material | OD (mm) | Thickness (mm) |
|---|---|---|---|
| Core / electron reservoir | Neodymium (NdFeB) | 20.728 | 10.364 |
| Dielectric / dam wall | Nylon / PTFE | 24.546 | 1.909 |
| Printed magnetic accelerator | Ferrite / Cobalt | 29.13 | 2.292 |
| Emitter / eddy surface | Aluminium | 37.982 | 4.426 |
Stators — inner / middle / outer
| Ring | Material | ID | OD | Thickness | Rollers |
|---|---|---|---|---|---|
| Inner | Neodymium | 104.211 | 120.594 | 8.191 | 12 |
| Nylon | — | 126.588 | 2.997 | ||
| Ferrite | — | 134.66 | 4.036 | ||
| Aluminium | — | 152.4 | 8.87 | ||
| Middle | Neodymium | 234.364 | 250.746 | 8.191 | 22 |
| Nylon | — | 256.74 | 2.997 | ||
| Ferrite | — | 264.812 | 4.036 | ||
| Aluminium | — | 282.552 | 8.87 | ||
| Outer | Neodymium | 364.516 | 380.898 | 8.191 | 32 |
| Nylon | — | 386.892 | 2.997 | ||
| Ferrite | — | 394.964 | 4.036 | ||
| Aluminium | — | 412.704 | 8.87 |
Real Shopping List
Magnetization
Control
Magnetization Coil Construction
The magnetization coil is the single most important tool in the whole build. It has two superimposed windings: a thick 200-turn DC base, and a 10-turn copper strip AC layer wound on top of it.
┌─────────────────────────────────────────────┐
│ 10-turn copper strip (AC 0.1–0.2 A, 1–3 MHz) ← outer layer
│─────────────────────────────────────────────│
│ 200-turn thick copper (DC 150–180 A) ← inner anchor
│─────────────────────────────────────────────│
│ plastic form / bobbin │
│─────────────────────────────────────────────│
│ BLIND │ ← roller or plate
│ (the piece to print) │
└─────────────────────────────────────────────┘
Procedure (Searl's 7 steps)
- Place the piece (roller stack of 8 segments, or full stator ring) inside the coil's blind.
- Set DC supply to 150–180 A and AC generator to 1–3 MHz sine at 0.1–0.2 A RMS.
- Switch DC and AC on simultaneously, ideally at a zero-crossing of the AC.
- Hold for exactly 9 seconds — the field grabs a circumferential wave pattern into the ferrite.
- Switch DC and AC off simultaneously at the next zero-crossing.
- Remove the piece without changing anything on the rig.
- Repeat for every roller and every plate — same coil, same parameters, same cycle.
IGV Propulsion System (Inverse Gravity Vehicle)
When the SEG is scaled up and embedded in the hull of a craft, it becomes an IGV — an Inverse Gravity Vehicle. Searl documented three simultaneous propulsion mechanisms produced by a single IGV unit.
The IGV's rotating vortex couples with the gravitational field and is repelled by it. Inside the cabin the crew still feels roughly half-gravity — no adverse effects.
Orbital motion of the roller mass on the outer ring generates a net thrust vector, steerable by modulating the inner ring's frequency.
Atmospheric pressure gradient: ionized air rushes radially outward, creating a low-pressure dome that lifts the craft without combustion.
Control is achieved with a high-power RF transmitter tuned to the same frequency used during magnetization. Change the frequency, change the behavior. This is why Searl said “frequency is the throttle”.
Observed Self-Running Effects
Pink ionization halo around the periphery and strong ozone smell.
Air flows radially outward; candles placed at the center extinguish.
Temperature drops progressively — more power extracted = colder device.
At roughly 4 K the whole SEG becomes superconducting.
Objects inside the ring lose apparent weight; full levitation at higher RPM.
Radios nearby switch on spontaneously during operation.
Searl's Own Words
“Existe un número mínimo de rodillos, al superarlo: el sistema arranca solo, acelera, se estabiliza y podrás tener un SEG funcional.”
“Tuve dos sueños principales. El primero mostraba las matemáticas que debía usar. A través de esos cuadrados comprendí la Ley de los Cuadrados.”
“El segundo sueño mostraba un sistema circular, como una rueda de bicicleta, con líneas que salían hacia afuera. Ese sistema se incendiaba y yo estaba en el centro.”
“Por la paz — MUCHA SABIDURIA.”
“Cambiar el arte de la combustión por la tecnología de la gravedad inversa.”
Step Up AI — Ask about Searl's SEG
Step Up AI — John Searl
Supports markdown, formulas, tables, code & simulation charts
Hello! I'm Step Up AI for John Searl. Ask me anything about the physics, circuits, or formulas. I can run simulations — describe your goal and I will iterate until we MATCH it.